Complaint
KYA-890 Automatic Electric Rebar Tying Machine
KYA-890 Automatic Electric Rebar Tier Machine is a hand held machine used to pack rebars quickly, It can save 3-5 times than man power by hand.Reasonable structure, advanced craft, simple and convenient operation, high efficiency and convenient maintenance.The Tying Machine is used for building market, including civil building, floor pipe, heating floor mesh, steel bar, etc.
Lightweight and compact body.
ne and half hour fast charging.
Modular components,easier maintenance
Reduced tying time.
| Model: | KYA-890 Automatic Electric Rebar Tying Machine |
| Air Tool Type: | Rebar Tier |
| Tying Rebar Diameter: | 8-34mm |
| Voltage & Capacity: | DC12.8V(4.4AH) |
| Charge Time: | Approx.90mins |
| Tying Speed Per Knot: | 0.80 seconds |
| Ties Per Charge: | Over 3000knots |
| Tying length/knot: | 300-500mm |
| Length Of Wire Coil: | 110M |
| Diamater Of Wire: | 0.80mm |
| Wraps Per Tie: | 2 wraps |
Length:0.8mm/0.03in
Material: low carbon steel tie wire have been heat treated, it is durable, flexible, anti-corrosion, anti-oxidation.
Smooth Surface:The surface of this tire wire is smooth, highly polished and has no burr.
Applicable Scope:Applicable scope of steel strapping: 6-24mm,6-25mm,8-34mm,9-28mm,20-45mm,30-58mm,30-60mm.
Reasonable Size:Each coil of tire wire is 110m/360ft long and its diameter is 0.8mm/0.03in.
Features:
Ergonomic rubberized soft handle for increased comfort.
Make ties in under 1 second 2-mode operation provides 2 or 3 wraps.
Fast and easy-load wire reel loading with protective cover.
Brushless Motor eliminates carbon brushes, enabling run cooler , efficiently for longer life.
Delivers up to 130 ties per wire reel allowing for maximum productivity.
Trigger power switch with lock-off feature requires two actions to power the tool.
Ergonomic rubberized soft handle for increased comfort Weighs only 4.19 lbs.
With battery for reduced operator fatigue.
| No | Normal | Common faults | Warning voice | Possible reason | Inspecting items | Solution | |||||||
| 1 | Power ON→ The Tip Axis is initialized and the wire-cutter operates automatically. | No operation takes place | No sound emitted | Battery completely empty | Confirm the battery is charged. | Perform normal charge. | |||||||
| Electrode plate has been oxidized | Take out the battery and see if the electrode has been brown. | Polish terminal part of battery pack with dry cloth, etc | |||||||||||
| Continuous short beeps(Pi,pi,pi…) | Curl guide is open | Open/close curl guide. | Fully close curl guide. | ||||||||||
| Binding wire has been entangled around Twist section. | Turn off power and take out the battery to confirm if binding wire has been entangled inside curl guide. | Turn off power, remove binding wire inside curl guide | |||||||||||
| Two long beeps | Battery Is empty | Confirm the battery is charged | Perform normal charge | ||||||||||
| 2 | Trigger ON→ Wire is sent out. | No wire is sent out | Continuous short | Curl guide is open | Open/close curl guide | Fully close curl guide | |||||||
| Three short beeps repeated(Pi,pi,pi,Pi,pi,pi, …) | Tie-wire has been run out | Check if the Tie-wire has been run | Set the new tie wire | ||||||||||
| Wire caught inside reel | Check if wire inside reel has been loosened and caught | Remove fray on reel | |||||||||||
| Cutter section is blocked with foreign substance | Confirm functioning of Cutter section | Either wipe Cutter section with dry cloth or blow it with air | |||||||||||
| A wire is caught in the cutter section or Wire guide A | Check if any wire is caught. | Diassemble the cutter section and remove the caught wire | |||||||||||
| 3 | Binding wire draws a circle. | Curl is disordered and steps out of curl | No sound emitted | Wire, by hitting reinforcing bars, was repelled | check if wire hits reinforcing bars at binding | Pay attention so that wire does not hit reinforcing bars at binding | |||||||
| 4 | Wire is subject to cutting | No wire cutting takes place. | No sound emitted | Cutter section is blocked with foreign substance | Confirm function of Cutter section. | Either wipe Cutter section with dry cloth or blow it with air | |||||||
| 5 | Wire twisting takes place | Wire gets entangled | No sound emitted | Wire, by hitting reinforcing bars,was repelled | Check if wire hits reinforcing bars at binding | Pay attention so that wire does not hit reinforcing bars at binding. | |||||||
| Binding power is week | No sound emitted | Reinforcing bars is not of designated size. | Confirm size of reinforcing bars to be bound | Use approriate diameter scope | |||||||||
| Erroneous handling such as improper application of machine | Confirm how to apply machine to reinforcing bars | Adjust the Torque to a higher lever and insert in vertical direction. Use as tilting at45° | |||||||||||
| Twisting-off takes place | No sound emitted | Reinforcing bars is not of designated size | Confirm size of reinforcing bars to be bound | Use approriate diameter scope | |||||||||
| Erroneous handling such as improper application of machine | Confirm how to apply machine to reinforcing bars | Adjust the Torque to a lower lever and insert in vertical direction. Use as tilting at45° | |||||||||||
| Works properly | Two long beeps repeated(Pi-pi, pi-pi,...) | Low power remains in the battery pack | Confirm the battery is fully charged. | Perform normal charge | |||||||||
| Four short beeps repeated(Pipipipi, Pipipipi,…) | The tool is used at high temperature. | Check the temperature at the job site. | Leave the tool and the battery pack at normal temperature in the room for some time. and then continue the operation. | ||||||||||
